全海深双球连接耐压舱的结构设计探索

钛合金耐压球壳被广泛地应用于大深度载人潜水器.但是,由于受到材料强度的限制,若采用成熟的Ti-6Al-4VELI来设计3人型的全海深载人舱,其壁厚将超出很多国家的现有制造能力.为了解决这一矛盾,该文提出了一种新的双球连接的方案,并以中国船级社最新的强度标准作为优化约束条件,用有限元分析法对这种结构形式进行了优化设计.最后,对双球结构方案与传统单球方案作了比较.     

Speed variation during peak and off-peak hours on urban arterials in Shanghai

Increased speed variation on urban arterials is associated with reductions in both operational performance and safety. Traffic flow, mean speed, traffic control parameters and geometric design features are known to affect speed variation. An exploratory study of the relationships among these variables could provide a foundation for improving the operational and safety performance of urban arterials, however, such a study has been hampered by problems in measuring speeds. The measurement of speed has traditionally been accomplished using spot speed collection methods such as radar, laser and loop detectors. These methods can cover only limited locations, and consequently are not able to capture speed distributions along an entire network, or even throughout any single road segment. In Shanghai, it is possible to acquire the speed distribution of any roadway segment, over any period of interest, by capturing data from Shanghai’s 50,000+ taxis equipped with Global Positional Systems (GPS). These data, hereafter called Floating Car Data, were used to calculate mean speed and speed variation on 234 road segments from eight urban arterials in downtown Shanghai. Hierarchical models with random variables were developed to account for spatial correlations among segments within each arterial and heterogeneities among arterials. Considering that traffic demand changes throughout the day, AM peak, Noon off-peak, and PM peak hours were studied separately. Results showed that increases in number of lanes and number of access points, the presence of bus stops and increases in mean speed were all associated with increased speed variation, and that increases in traffic volume and traffic signal green times were associated with reduced speed variation. These findings can be used by engineers to minimize speed differences during the road network planning stage and continuing through the traffic management phase.     

船体板格极限强度数值计算影响因素及敏感分析

船体板格极限强度的有限元计算方法应用广泛,但其计算方法具有一定的不稳定性,计算结果受多种因素的影响.本文针对船体板格有限元计算方法的不稳定性进行研究,通过将有限元计算结果与其他学者的研究成果进行对比,验证本文所采用的有限元方法的可靠性,然后针对板格材料、初始缺陷、网格密度、边界条件等几种因素的敏感性进行具体研究,发现理想应力应变关系会使得结果偏于危险.网格形状和网格密度对于结果均有影响,边界条件对于有限元结果有影响,最大误差在7.2%,并且模型3会使得结果偏于危险.初始缺陷是一敏感因素,最大误差在20%,因此需要根据实际缺陷选取合适的屈曲模态和比例因子.     

焊接残余应力对深潜器耐压球壳承载能力的影响

耐压球壳通常采用焊接方式将两个半球壳连接成整球,在焊缝处产生的接近材料屈服强度的焊接残余应力对球壳的承载能力有多大的影响,是否需要做焊后消除残余应力处理,将直接影响球壳的安全性和生产成本。而现有对球壳极限强度计算,无论是理论计算还是数值计算,均只考虑了球壳初始缺陷中的几何缺陷对球壳极限强度的影响。该文将在现有的耐压壳极限强度设计公式基础上,采用数值计算的方法对耐压球壳的焊接过程进行数值模拟,得到焊后球壳的焊接残余应力分布,并在此基础上考虑残余应力对球壳极限强度的影响,结果表明,对于大潜深厚球壳,焊接残余应力对耐压球壳承载能力影响不显著,为大深度潜器耐压球罐是否需做焊后消除残余应力处理提供了一定的参考依据。     

基于改进移动最小二乘法的结构可靠性分析

基于改进移动最小二乘法对结构可靠性问题进行分析,数值模拟结果表明,改进方法可有效提高计算精度.具体方法是使用椭圆范数代替二范数来度量样本点到中心点的距离,并根据上次迭代所得到的响应面在中心点处的法向量与坐标轴所成角度,对影响域进行旋转变换;从而将样本点的权重大小由样本点与中心点、响应面的距离共同决定,并将每次迭代得到的响应面函数在中心点处的法向信息包含在内.     

Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

压载荷下骨材贯穿孔孔边应力集中模型试验

以船舶双层底结构为研究对象开展模型试验,研究板材中的开孔在承受压力载荷作用下的孔边应力分布情况,分析压力载荷下不同开孔孔型以及不同补强结构对孔边应力分布情况的影响。在此基础上,开展相关仿真分析,将试验结果与有限元仿真结果进行对比,验证有限元仿真的准确性。     

放宽条件定点集结模式下编组站车辆 集结排队系统分析

集结模式决定了货车集结过程的结束条件，定点集结是一种高效率的集结方式，有利于提高运输质量.针对放宽条件定点集结模式下编组站车辆集结过程，建立离散时间批到达批服务排队模型，利用嵌入式马尔可夫链方法求得离去时刻瞬时系统集结车辆队长分布，并求得任意时刻车辆集结队长分布，在此基础上分别分析了最小编成辆数，车组大小分布，车流到达强度，服务时间间隔分布对车辆平均集结队长，集结延误时间，效率，一昼夜发送车流量等系统指标的影响.分析结果表明，各因素对车辆集结排队系统影响明显.因此，利用本文提出的模型能为编组站的精细化管理和车流组织优化提供决策参考.     

兰新高速铁路高寒地段路基温度场数值模拟分析

兰新高铁浩门至大梁区间所处地区海拔高,气温低,冻结期长,属于深季节性冻土区。为解决该区间路基冻害问题,依据当地气候条件,运用ANSYS有限元分析软件,对低路堤、零断面换填路基及不同深度处铺设保温材料的路基温度场进行数值模拟,分析路基冻结深度的变化规律和最大冻结深度,为高寒区高速铁路路基冻害防治措施设计提供参考。研究表明:(1)由于兰新高铁浩门至大梁区间海拔高、冬季冻结时间长、气温低等原因,导致路基冻结深度大;(2)零断面换填路基实测地温和数值模拟计算结果基本相符,所选计算模型、参数等可以为其他相同条件断面数值模拟分析采用;(3)铺设保温板路基温度场较未铺设保温板的0℃线上移,冻结深度增加速率变小,最大冻结深度明显减小,路基保温效果较好;(4)由于路基边坡、基床以下部位土层性质、厚度、热物理参数等影响,低路堤最大冻结深度比零断面换填路基大。     

带支撑梁的船闸闸室裂缝成因分析

针对某船闸闸室施工期在支撑梁上部出现表面裂缝的问题,基于有限元原理,分析闸室表面裂缝的成因及分布规律,并提出防止表面裂缝产生的温控措施.分析结果表明:早期在支撑梁上部出现表面裂缝主要是因为内外温差以及支撑梁对新浇筑混凝土的约束作用;在控制浇筑温度的基础上,采取表面保温和内部水管冷却相结合的温控措施,可以将表面点的抗裂安全系数提高至1. 40.该方案在后续施工应用后未出现表面裂缝,达到了良好的防裂效果.